Tsatu logo
ISSN: 2524-0714

Please use this identifier to cite or link to this item: http://elar.tsatu.edu.ua/handle/123456789/12962
Full metadata record
DC FieldValueLanguage
dc.contributor.authorКолодий, Александр Сергеевич-
dc.contributor.authorКолодій, Олександр Сергійович-
dc.contributor.authorKolodii, Oleksandr-
dc.contributor.authorСушко, Ольга Викторовна-
dc.contributor.authorСушко, Ольга Вікторівна-
dc.contributor.authorSushko, Olha-
dc.date.accessioned2021-02-03T12:26:26Z-
dc.date.available2021-02-03T12:26:26Z-
dc.date.issued2020-
dc.identifier.urihttp://elar.tsatu.edu.ua/handle/123456789/12962-
dc.description.abstractUK: В роботі розглянуті питання, пов’язані з впливом на сили різання середовища, нанесеного на оброблювану поверхню у вигляді шару стеаринової кислоти, а також явищ, які при цьому відбуваються в механізмі різання. Тверді змазки, які наносяться на оброблювальну поверхню, показали, що навіть без подачі на передню грань різця рідкої змазки можна досягнути такого ж позитивного ефекту збільшення коефіцієнту різання (кута зсуву), зменшення сил різання та покращення стану обробленої поверхні, який досягається в умовах різання із застосуванням змащувально-охолоджуючої рідини. Тому при дослідженнях можливо застосовувати ті ж самі методи, які використовуються у випадку вивчення процесів різання із застосуванням звичайних методів подачі змащувально-охолоджуючої рідини. RU: В работе рассмотрены вопросы, связанные с влиянием на силы резания среды, нанесенной на обрабатываемую поверхность в виде слоя стеариновой кислоты, а также явлений, происходящих при этом в механизме резания. Твердые смазки, наносимые на обрабатываемую поверхность, показали, что даже без подачи на переднюю грань резца жидкой смазки можно достигнуть такого жеположительного эффекта увеличения коэффициента резания (угла сдвига), уменьшения сил резания и улучшения состояния обработанной поверхности, какой достигается в условиях резания с применением смазочно-охлаждающей жидкости. Поэтому возможно применять те же самые методы, какие используются в случае изучения резания с применением обычных методов подачи смазочно-охлаждающей жидкости. Проведенные экспериментальные исследования позволили установить, что наличие среды, нанесенной в виде покрытия на обрабатываемую поверхность, приводит к увеличению угла сдвига материала и к снижению сил сопротивления резанию. Однако, с другой стороны, способствует увеличению коэффициента трения на передней грани резца. Это указывает на то, что среду, наносимую на поверхность, следует выбирать с учетом свойств обрабатываемого материала. EN: The article discusses the issues related to the influence on the cutting forces of the medium, which is applied to the treated surface in the form of a layer of stearic acid, as well as the phenomena occurring in this process in the cutting mechanism. Solid lubricants applied to the machined surface showed that even without supplying liquid lubricant to the cutting edge of the tool, they have the same positive effect of increasing the cutting ratio (shear angle), reducing cutting forces and improving the condition of the machined surface, which is achieved under cutting conditions using cutting fluid. Therefore, the same methods can be used to study the phenomena occurring in this case as in the case of a conventional supply of cutting fluid. Taking into account the inevitable costs, as well as the environmental aspects associated with the use of liquid lubricating process agents, the use of such media that can be used for the most complete implementation of the minimum lubrication technology is very relevant and promising. The process was investigated using a cutting tool made of T15K6 material with different values of the rake angle (α = 20 °, 25 °, 30 °, 35 °) and the value of the clearance angle γ = 6 ° on various materials: copper, mild steel, aluminum, brass. The cutting coefficient was determined from the results of measuring the chip length. The dependence of the cutting resistance on the depth of cut for processing without coating and with coating has been established; thanks to the model of orthogonal cutting, the general features of the mechanism during cutting are revealed, and the influence of the thickness of the cut layer on the depth of cut is established The carried out experimental studies made it possible to establish that the presence of a medium applied in the form of a coating on the surface to be treated leads to an increase in the shear angle of the material and to a decrease in the cutting resistance forces. However, on the other hand, this contributes to an increase in the coefficient of friction at the leading edge of the tool (cutter). This indicates that the medium to be applied to the surface should be selected taking into account the properties of the material to be treated.uk
dc.language.isoruuk
dc.publisherТДАТУuk
dc.relation.ispartofseriesНауковий вісник ТДАТУ;Вип. 10, т. 2-
dc.subjectрежими різанняuk
dc.subjectзмащувально-охолоджувальні технологічні речовиниuk
dc.subjectстеаринова кислотаuk
dc.subjectкут зсувуuk
dc.subjectопір різаннюuk
dc.subjectрежимы резанияuk
dc.subjectсмазочно-охлаждающие технологические средстваuk
dc.subjectстеариновая кислотаuk
dc.subjectугол сдвигаuk
dc.subjectсопротивление резаниюuk
dc.subjectcutting conditionsuk
dc.subjectlubricating and cooling technological meansuk
dc.subjectstearic aciduk
dc.subjectshear angleuk
dc.subjectcutting resistanceuk
dc.titleВлияние среды, нанесенной на обрабатываемую поверхность, на процесс резанияuk
dc.title.alternativeВплив середовища, нанесеного на оброблювальну поверхню, на процес різанняuk
dc.title.alternativeInfluence of the medium applied to the worked surface on the cutting processuk
dc.typeArticleuk
Appears in Collections:кафедра Технології конструційних матеріалів

Files in This Item:
File Description SizeFormat 
Науковий вісник ТДАТУ 2020 Випуск 10, Том 2-192-201.pdf332.9 kBAdobe PDFThumbnail
View/Open
Show simple item record ???jsp.display-item.check???


Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.